![]() ![]() The drive is subject to its own examination. There must be a manufacturer declaration for the coupling. The coupling and motor must be examined separately. Marking The marking on the pump refers only to the pump part. Kanten din iso 13715 tolerance museum serial number#The item numbers used in the user manual in sections 1-8 are not identical with the item numbers referred to in the parts lists and associated drawings in Section 9!Īssignment of the user manual The metering or process pump type and serial number are referred to on the cover, in the data sheet (section 1.2.1) and on the nameplate of the metering or process pump. “1 General remarks – 1.1 Safety Instructions”. The right header indicates the section in which the reader actually is at the moment, e.g. The numbering of figures and the cross-references to figures and pages are only valid within a coherent section. ![]() In this way, the length of such a section can be determined. The pages are numbered according to the example "/11" ( of a total of 11 pages of the coherent section). The page numbering in the footer is only carried out in sequence throughout a coherent section. Kanten din iso 13715 tolerance museum series#It is thus possible that point 3.3 "Pump Head" only contains section 3.3.3 "PTFE series", since the other series treated in sections 3.3.* are not relevant for your specific metering or process pump. Motor / Accessories (if they exist) CE declarations / Manufacturer declarations In some sections of 3 "Components", 4 “Installation” and 5 “Operation” a sequential numbering of sections may not always be adhered to. Finding the required information has been simplified by dividing the user manual into the following sections: 1. ![]() For this reason, the pages and sections are not numbered in sequence throughout the whole document. Thus each manual only contains information on the pump supplied. Structure, Assignment, Marking, Ordering of Spare Parts Structure of the user manual Just like the metering or rather process pump, this user manual has a modular structure. Table of contents 1 General remarks 1.0 Structure, Assignment, Marking, Ordering of Spare Parts 1.1 Safety instructions 1.1.1 Safety instructions in Ex areas 1.2 Technical data 1.2.1 Data sheet 1.2.2 Dimension sheetģ Components 3.1.12 Gearbox H2, H3, H4, H5, H6, G3H, G4H 3.2.20 Pneumatic stroke length adjustment (H2.H6, C, KH, DH, DSH) 3.3.3 Diaphragm pump head (PTFE – diaphragm) 3.4.13 Plunger seal: diaphragm pump head 3.5.14 Plunger restraint (H2, J, K, KA) 3.6 ValvesĤ Installation 4.1.1 Installation of machines 4.2 Suction and pressure piping 4.3.1 Examples of suction and pressure piping designsĥ Operation 5.1.19 Lubricant and lubricant change (H2.H6, G3H, G4H) 5.2.4 Gear oil for H2, H3, H4, H5, H6, G3H, G4H 5.2.10 Lubricant table 5.3.1 Startup procedure NOVADOS 5.4.1 Adjusting the capacityĦ Maintenance, Inspection, Cleaning 6.1 Maintenance, Inspection, Cleaning 6.2 Technical informationħ Troubleshooting 8 Transport, Storage, Preservation 8.1 NOVADOSĩ Drawings and parts lists Dimension sheetĭrawings Parts Lists Parts Lists (Service Set) Parts Lists (Accessories)ġ0 Motor / Accessories 10.1 Motor 10.3 Pressure Transmitter EJA (YOKOGAWA) 10.3 Coupling (BoWex) ATEX 10.3 PumpĬE declarations / Manufacturer declarations CE declaration (SPX) CE declaration motor CE declaration pressure transmitter (YOKOGAWA) CE declaration coupling (BoWex)ġ General remarks 1.0 Structure, Assignment, Marking, Ordering of Spare Parts Edition 01/2018 COPYRIGHT ©2018 SPX FLOW, Inc.īRAN+LUEBBE Customer service Technical Hotline Spare parts National International Mail Other Fax No part of this manual may be reproduced or transmitted in any form or by any means, electronic or mechanical, without the prior written permission of SPX Flow Technology Germany GmbH. Information in this manual is subject to change without notice and does not rep resent a commitment on the part of SPX Flow Technology Germany GmbH. SPX Flow Technology Germany GmbH has a tightlyknit, global network of service centres and partners. For more details, just contact us and we will discuss how we can help you to optimise your processes! ORIGINAL INSTRUCTIONS READ AND UNDERSTAND THIS MANUAL, PRIOR TO INSTALLATION, OPERATING OR SERVICING ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |